WARNING: This product can expose you to chemicals including lead and lead compounds which are known to the State of California to cause cancer and reproductive harm. Prop 65 Warning

Gas Bottle & Cylinder Storage Cage - Single Vertical 5-10 cylinder. Secure propane and other gas bottles in pad-lockable cages. Limit access to authorized personnel. Use different sizes and multiple cages to provide proper separation between incompatible gases. Solid welded angle frame construction provides years of service. Easily relocated. Shipped fully assembled. Open steel mesh from sturdy expanded metal construction prevents gases from accumulating. Construction provides compliance with NFPA codes and OSHA regulations.

The TC signs are a collection of non-standard traffic control (TC) signs that have been 'officially approved' as required by the Transport Operations (Road Use ...

Knight Riderlightbar illegal

What if there was no, No Left Turn sign on a road where all the traffic was going right? If it were the case, you'd have a dangerous situation on your hands ...

Keep vehicles out of restricted areas with our 816 No Through Road Sign. Class 2 R2/RA2 reflectivity for visibility at night. Can be mounted on walls or ...

As a quick followup to this, you could put some dividers inside of the cube, set just forward of the sphere/cylinder, to simulate the 'black bars' that you see as the light is scanning back and forth.

Quick and dirty setup with Primitives. Sphere inside an elongated cube with an orange plastic shader surrounded on five sides with black planes. Play with emmisive values on the sphere and cube and you may get close to what you want. Duplicate it and put them in a row, increasing and decreasing the emmisive values on each block to give the moving light apperance.

21,150 Lumens - 150 Watt - 5000 Kelvin - UFO LED High Bay Sensor Ready Light Fixture 400 Watt Metal Halide Equal - Black Finish - 277-480 Volt - PLT-12691.

Knight Riderlightfor truck

The All New NiteRider Lumina Dual 1800 represents the next evolution of our best-selling Lumina headlight into a dual LED set-up that produces a far ...

This would work. My initial intention was that this would be a single unit of the light bar. Duplicatiing this so that you have a row of them, so each has the distinctive centre light and darker surround as shown in the picture above. Changing the emissive values of each unit to make it lighter/darker in progression for animation if needed. As it is made of DAZ Primitives it shouldn't be too heavy on resources :)

KITTscanner

Once you get this working, you could then take the rectangle and dividers into Hexagon, and then pull the lower side corners forward to better 'fit' the angle of your Camaro.  You could then use the geometry editor to delete part of the grille or hood if needed, and set the scan assembly inside of the grill/just under the hood.

And, this was probably implied, you could then move the emmissive sphere back and forth along one axis to simulate the 'scanning' effect.  And this should be easy to animate, should you be looking to do a short video...

KITTKnight Rider lights

You can make any surface a light emitter in Iray. try taking the camaro, load it and get it all set up. then create a primitive cube with the lowest number of sides. Scale it and place it where the light should be on the car. then apply an iray light shader to it and play with the settings, it's fairly easy.

Quick and dirty setup with Primitives. Sphere inside an elongated cube with an orange plastic shader surrounded on five sides with black planes. Play with emmisive values on the sphere and cube and you may get close to what you want. Duplicate it and put them in a row, increasing and decreasing the emmisive values on each block to give the moving light apperance.

And, this was probably implied, you could then move the emmissive sphere back and forth along one axis to simulate the 'scanning' effect.  And this should be easy to animate, should you be looking to do a short video...

Knight RiderlightBar with sound

You could try a row of 'light cubes' and turning each one on\off you could simulate that way. A simple red light texture would probably be needed for the right effect.

Gas Cages From Stock · Gas Bottle Storage Cage - 40kg · Gas Bottle Storage Cage - 50kg · Tradesafe Modular Fully Galvanised Gas Cage 1.0m x 0.5m x 0.9m (Includes ...

Buy a Road Narrows Symbol Sign for your city, school zone, or municipal government streets, roads and parking lots. We sell Warning Signs that are MUTCD ...

Knight Riderlightfor car

Parking Signs - everybody needs parking signs! Lots of designs to choose from - easy to order online. Long lasting, outdoor grade signs.

We have a great selection of information signs that are ideal for display in warehouses, schools, offices or anywhere else where people would benefit from easy ...

I want to create a new version of KITT using a model of a new Camero from another site.  I can't quite figure out how to do the scanner lights on the front.  I tried searching for something similar online, but to no avail.  Does anyone know where I could find somethimg that would work, or perhaps an easy way to make them?  I have no modeling experience at all.

Ironman 4x4's LED Light Bars allow you to see further and draw less power, with state of the art, high intensity CREE LED's for maximum light spread.

DAZ Productions, Inc. 7533 S Center View Ct #4664 West Jordan, UT 84084

JavaScript seems to be disabled in your browser. You must have JavaScript enabled in your browser to utilize the functionality of this website.